2023년 가장 많이 본 제조 과정 영상 몰아보기. 훌륭한 한국의 제조 과정 TOP 7! / TOP 7 excellent Korean manufacturing processes!

2023년 가장 많이 본 제조 과정 영상 몰아보기. 훌륭한 한국의 제조 과정 TOP 7! / TOP 7 excellent Korean manufacturing processes!

[ The process of making beef jerky ] Maintain the cleanliness of workers before entering the workplace. When meat is received, it goes through a thawing process. Place the thawed meat in a bowl. Thawed meat goes through a selection process. Removes fat or fascia. Remove it once more with the machine.

Make seasoning for beef jerky. The prepared seasoning is put into the machine and the meat is cured. The injector soaks in the seasoning of the meat. Cuts the meat to a certain size. Put the meat in the vat. The vat rotates to marinate the meat. Cured beef

Cover with wrap and marinate for 2 days at low temperature. Meat that has been aged goes through a molding step. Spread the meat on the hook so that it does not overlap. It goes through a drying process. Dry for at least 100 minutes on high heat.

The well-dried beef jerky is separated from the rings. Cut the beef jerky into bite-size pieces. It passes through a metal detector to check if there are any foreign metals. It goes through a packaging stage. Divide the beef jerky into portions by weight.

Seal the product by putting the product together with the oxygen scavenger. It is inspected by passing it through a weight checker and metal detector once more. It goes through the external packaging stage. Enter the expiration date. [ The process of making a power strip ] Assemble the parts to the power strip body.

After the assembly of the main body is finished, the line of the power strip is produced. Cut the line to a certain length. Strip the end of the wires. Peel off the top part of the wire. Attach the grounding plug to the wire. Inject the plug.

It binds the parts so that they can be connected to the main body of the power strip. Separate the created cords by winding them one by one. Go through assembly steps. Assemble the power strip body and code. Solder the assembled parts. Cover the main body and inspect for defects.

Combine the power strip with the press machine once more. It goes through a packaging stage. Seal the vinyl. Finally, I will give you some common sense that you must know when using a power strip.

Usually, the recommended cycle for replacing a power strip is 2 years, and it is good to check the wattage before using the product. There are many hair dryers with higher wattage than expected, so be sure to check before using.

It is recommended that the switch capacity is less than 1000W per district, so it is said that it is a safe way to use a power strip not to use products with more output than that. [ The process of making a camping car ] First, start by removing the chair.

To make a camper, you need to remove all the finishing materials from the vehicle. Constantly tearing it apart. Thinking of leaving only the car body, I removed all of them. Van with only the body left

They are in the process of installing a heater that works without starting the engine, which is the basics of a camper. Since the heater is used without starting the engine, it is directly connected to the fuel tank. The fire extinguisher under the driver’s seat should be located elsewhere and fitted with a heater.

Connect the tube so that warm air can come out. A hole is drilled and an outlet is attached so that electricity can be used from the outside of the vehicle. The car body is not flat, so the height is adjusted by laying wood. Continue to work.

Apply insulation to the car body before putting in furniture and beds. Cut the protruding parts of the car body one by one to make it flat. Apply insulation to the entire floor. The sides are also thoroughly insulated.

A fan is installed to ventilate the camper, and for that purpose, a hole is drilled in the roof surface. After drilling a hole large enough to install the ventilator fan, apply insulation to the roof as well. Take measurements. Design to size.

After finishing the design work on the computer, the wood is cut using a CNC machine. Since the CEO works alone, he cuts and assembles all furniture using a CNC machine. Grind the rough side of the wood. Basically, the upper part of the car body is fixed with wood.

It’s a very difficult job, but I’m working on it meticulously. Cut the tree to the length of the ceiling. Put the wood in the frame you made and drill holes evenly. Place the cut wood on the ceiling and fix it. Both sides are curved and cut to fit the shape. Neatly tidy ceiling

From now on, he will put wood on the floor. Create a chest of drawers and bed to install on the floor. Wood glue It fixes well. It is fixed well so that it does not wobble. He continues to assemble and install wood cut on a CNC machine.

It makes the side with the window neat. Continue the CNC work. It coats the wood. From now on, he will work on the details of the interior of the car. Lay out wood to finish the floor. He installs various cabinets and details.

Create a cabinet to fit between the driver’s seat and the bed. The driver’s seat needs to be adjusted, so the cabinet also creates a sliding cabinet that moves back and forth. Place the cabinets one by one and secure them well. Install the ventilator fan. Put lights on the ceiling.

Continue to do the finishing touches. He installs cabinet doors and makes storage boxes. Lay out the mattress. I watched it for a week and a lot of process and effort went into it. [ The process of making a radiator ] Cold-rolled steel sheets produced by POSCO are cut to size and used.

Create the radiator shape using a press machine. Once the radiator shape is made, punch holes on both sides with a press machine. The edge part is neatly made with a press machine. After the pressing process, the two fittings are welded together. More meticulous welding of fittings made from one piece.

The edges are also welded. When each part is completed, the parts are welded together according to the size and capacity of the radiator. Hole parts are welded and joined together. After welding is completed, it goes through an inspection process. Check the product for defects for punctures. Products with no defects

When the product is confirmed to be free from defects, it goes through the painting process. Each product has a different color, and special powder coating is applied. After the powder coating is completed, the product is completed through a heat treatment process along the rail.

When the painting work is completed, the radiator assembly process is carried out. Put oil in the radiator. Oil with a very low thermal expansion coefficient and excellent thermal conductivity is used semi-permanently after being filled once. Assemble the radiator wiring. Connect the radiator to power. Check the power by plugging it into an outlet.

It goes through the radiator packaging stage. As long as it’s been a long time, many people’s hard work has been melted into one radiator. [ The process of making a special wood mirror ] Material warehouse First, he selects the right wood for the mirror from the warehouse. Level the wood.

Level the front in the same way. Place the wood on a wooden board and envision the shape of the mirror. When the concept is finished, it is measured. He continues to picture the image of a mirror in his head. Draw the shape of the mirror to match the shape of the wood.

He has to attach a mirror to the wood, so he draws a picture in a form that can bear the weight of the wood. Cut out according to the shape shown in the picture. Put a wooden board with a mirror pattern on it and mark the back of the wood.

Mark the back side of the wood as much as the thickness of the mirror. It neatly trims a wooden board imitated in the shape of a mirror. Check it one more time by holding it against a neatly trimmed wooden board. Dig the marked area to the thickness of the mirror.

Dig the back side where the mirror will be attached. Grind the front cleanly too. Wood with finished back processing Grind the back side. Grind the edges with hand sandpaper. The wooden board imitated in the shape of a mirror is delivered to a mirror manufacturer to make a mirror.

Make sure the manufactured mirror fits the wood well. Apply silicone to attach the mirror. Attach the mirror to the wood. In order to hang the wooden mirror on the wall, he measures and fabricates a frame that will be attached to the back of the mirror. Round the edges.

Cut the part to hang on the wall diagonally. Grind the wood. Make a frame shape and mark where the wooden core will be inserted. He drills a hole for the wooden dowel pin to be driven in. Apply wood glue. Insert the wooden dowel pin. He makes the frame.

Fix the frame and bond it securely. Grind the frame. Continue to finish with hand sandpaper. Mark the frame against the mirror. Drill a hole in the frame. Apply silicone according to the marked shape. Attach the frame to the back of the mirror. Insert the screw. He applies wood glue. Finish the screw holes.

Grind the surface cleanly. Grind the front of the mirror as well. Apply oil to finish. The oil varies depending on the characteristics of the wood, but usually 2 or 3 coats are applied and finished. [ The process of making exotic woods resin table ] Grind the wooden surface smooth. Remove wood shavings.

Change the machine to polish the wood surface to perfection. Apply the resin to the wooden surface. There are many small holes in the wood, so you need to apply resin first to block the pores to reduce air bubbles. Make a table frame according to the size of the tree.

Remove dust or foreign substances. Seal the corners of the table frame with silicone. The work being done must be done meticulously to prevent defects in the product. Cut the wood to fit the frame. Place the tree well into the frame. Remove dust.

It creates a necessary support when the resin is poured into the mold. Apply tape to prevent resin from getting on it. When the resin is poured and hardened, there is a part where the tree can float or deform, so raise the support. Mix the base and hardener to make resin for the table.

Pour resin into the mold. Resin work has different working hours depending on the season, but it usually lasts for a week. Eliminates air bubbles. Air bubbles form in the hole, and the resin is filled by pouring the resin and removing the air bubbles in turn. Results after a week

When the resin hardens, separate the frame. It does the leveling work. Grinds rough surfaces. Clean the borders of the table. Angle the corner of the table. Grind the surface. Grind the edge of the table. Then grind the surface smooth from 80 grit to 3000 sandpaper. Wipe the table with a wet towel.

Removes moisture. Grind the table surface with 3000 grit sandpaper. Working on table polish. First, apply a rough coat of gloss. Gives a secondary gloss. Wipe well with a dry towel. Finally he proceeds to work on the oil. Once the oil dries, the table is complete. [ The process of making fishing rods ]

Carbon fabric Cut the carbon fabric. Measure and cut according to the type and size of the fishing rod. Attach the cut carbon fabric to the mold. Roll the fabric attached to the mold into a fishing rod shape using a rolling machine.

The mold varies depending on the size and type of the fishing rod, and the process is the same: attaching and rolling the fabric. Taping is done by wrapping PP tape around a rolled carbon fabric. The taped fishing rod is placed in an electric furnace, dried and molded.

Separate the carbon fabric molded into the shape of a fishing rod from the mold. Remove the tape. Cut the fishing rod to make it a consistent length. Polishes rough surfaces to a smooth finish. Color painting is carried out on a well-dried fishing rod.

After coloring and drying the fishing rod, printing is carried out. They proceed to attach labels. Coating the fishing rod. After painting, dry the fishing rod well in the drying room. A well-dried fishing rod requires various parts to be joined together, so the parts where the parts will be joined are polished.

Go through the fishing rod parts assembly process. Depending on the type of fishing rod, various parts are combined and assembled by hand by workers. In the case of lure fishing rods, they proceed with attaching a guide. If a guide is attached, apply an epoxy coating.

Depending on the type of fishing rod, coating is performed on the fitting or connection parts. After coating and drying, the fishing rod goes through an inspection process. If there are any rough areas on the surface, the worker will check and smooth them out. Check that the guides are straight.

If there are no problems during the inspection process, the fishing rod assembly process is performed. By assembling it into a finished product, they inspect the product one more time carefully to make sure there are no problems. Once the fishing rod assembly and inspection are complete, they proceed to the packaging stage.

It takes a lot of time and process to make one fishing rod. I salute NS CEO and workers who produce excellent fishing rods. Thank you for watching so far. I’ll see you next time with a fun manufacturing video 🙂

스케일부터 다르다! 2023년 가장 많이 본 제조 과정 영상 몰아보기. 훌륭한 한국의 제조 과정 TOP 7! / TOP 7 excellent Korean manufacturing processes!

00:00 한국의 육포 제조 과정
11:28 한국의 멀티탭 제조 과정
22:37 한국의 캠핑카 제작 과정
47:05 한국의 라디에이터 제조 과정
56:00 한국의 특수목 거울 제작 과정
1:12:52 한국의 레진테이블 제작 과정
1:37:16 한국의 낚싯대 제조 과정

💌 문의 : factorytrip.std@gmail.com
-영상 제작에 도움을 주신 대표님과 관계자 여러분께 깊은 감사의 말씀을 전합니다.
-무료 촬영을 진행하여 소상공인/중소기업 분들에게 힘이 되는 팩토리트립이 되겠습니다.

🎥 Copyright(C) 2023 FactoryTrip All rights reserved.

#대량생산 #제조과정 #공장 #육포 #멀티탭 #캠핑카 #라디에이터 #특수목 #거울 #레진테이블 #낚시대 #낚시용품 #우드워킹 #생산 #과정 #제작 #제조 #전문가 #장인 #기술자 #beefjerky #powerstrips #powerbar #extensioncord #outletstrip #camper #campingcar #radiator #exoticwood #mirror #resin #resinart #resincrafts #resintable #fishing #fishingrod #woodworking #woodwork #woodart #factory #manufacturing #making #process #technology #technician #artisan #master #artificer #asmr